潛水排污泵（排污泵品質）

GERMANY KAYSEN

KAYSEN凱森潛水排污泵概述
潛水式排污泵采用大流道抗堵塞水力部件設計,，大大提高污物通過能力,，能有效地通過泵口徑的5倍纖維物質和直徑為泵口徑約50%的固體顆粒。設計合理,，配套電機合理，效率高,，節能效果顯著。潛水式排污泵機械密封采用雙道串聯密封,，材質為硬質耐磨碳化鎢,，具有耐用、耐磨等特點,，可以使泵安全連續運行800小時以上,。泵油室內設有油水探頭，當水泵側機械密封損壞后,，水進入油室,，探頭發生信號，對泵實施保護,。

可根據用戶需要配備全自動安全保護控制柜,，對泵的漏水，漏電,，過載及超溫等進行監控,，保證泵運行可靠安全。雙導軌自動耦合安裝系統,，給泵的安裝的安裝,，維修帶來了極大的方便，人可不必為此而進出污水坑,。浮球開關可根據所需的水位變化,。自動控制泵的停啟，無需專人看管,。電機運行不過載,。根據使用場合電機可采用水套式外第三者循環冷卻系統，能保證電泵在無水（干式）狀態下安全運行,。安裝方式有固定式自動耦合安裝和移動式自由安裝二種,，可滿足不同的使用場合。GERMANY KAYSEN

主要優點：

●結構緊湊,、占地面積小

●體積小

●振動噪聲小,電機溫升低,對環境無污染

●噪聲小

●節能效果顯著

●檢修方便

●連續運轉時間長

●不存在汽蝕破壞及灌引水等問題

主要特點：

●密封油室內設置有高精度抗干擾漏水檢測傳感器,，及定子繞組內預埋了熱敏元件，對水泵電機*保護,。

●潛水排污泵采用獨特的單葉片或雙葉片葉輪結構,，大大提高了污物通過能力，能有效地通過泵口徑的5倍纖物質與直徑為泵口徑約50%的固體顆粒,。

●可根據用戶需要配備全自動安全保護控制柜,，對泵的漏水、漏電，過載及超溫等進行*保護,，提高了產品的安全性與可靠性,。

●配浮球開關可以根據所需液位變化，自動控制泵的起動與停止,，不需專人看管,，使用極為方便。

●可根據用戶需要配備雙導軌自動耦合安裝系統,，它給安裝,、維修帶來極大方便，人可不必為此而進入污水坑

●能夠在全揚程范圍內使用,，而保證電機不會過載,。

●潛水排污泵有兩種不同的安裝方式，固定自動耦合安裝系統,、移動式自由安裝系統

●機械密封采有新型硬質耐腐蝕碳化鎢材料,，同時將密封改進為雙端面密封，使其長期處于油室內運行,，可使泵安全連續運行3000小時以上,。

。GERMANY KAYSEN

主要應用：

●城市污水處理廠排水系統

●農村,、沼氣池,、農田灌溉

●勘探、礦山配套附機

●住宅區的污水排水

●市政工程,、建筑工地

●人防系統排水站,、自來水廠的給水裝置

我們歡迎對現有產品或類似產品的技術升級以及新工藝、新產品的推廣,、引進,。

我們歡迎來圖來樣加工，許可貿易,。

我們歡迎成為國內代理或定點服務單位,。

我們不局限于在環保水處理方面的合作，對其它產品和市場的開發也不無興趣,。

總之,，我們作為一個整體，愿共同探討多種合作的可能性,，為廣大用戶提供優質的產品和完善的服務,，是您真誠的朋友！

We welcome the technological upgrade of existing products or similar products as well as the promotion and introduction of new processes and products.

We welcome drawings and samples for processing and license trade.

We welcome to become domestic agents or designated service units.

We are not limited to cooperation in environmental water treatment, and we are also interested in the development of other products and markets.

In short, as a whole, we are willing to discuss the possibility of multiple cooperation together, to provide customers with quality products and perfect services, and we are your sincere friends!

潛水排污泵維護與保養

為了保證潛水泵的正常使用壽命,，應該進行定期的檢查和保養：

l 底蓋的調整：在水中長期使用后,，葉輪與底蓋的間隙可能增大，造成水泵流量和效率下降，此時應切斷電源,，將水泵吊起,，松開固定螺釘，旋轉底蓋,，將間隙調整到0.3～0.5mm（僅用于AS,、AV和小型泵≤7.5kW）。

l 更換密封環：在水中長期使用后,，葉輪與底蓋的間隙可能增大，造成水泵流量和效率下降,，此時應切斷電源,，將水泵吊起，拆下底蓋,，取下密封環,，按葉輪口環實際尺寸配密封環，間隙一般在0.5mm左右（≥11kW的泵）,。

l 水泵長期不用時,應清洗并吊起水泵置于通風干燥處,。若置于水中，每隔15天至少運轉30min（不能干磨）以檢查其功能和適應性,寒冬季節注意防凍,。

l 電纜每年至少檢查一次,，若破損請立即給予更換。

l 每年至少檢查一次電機絕緣及緊固螺釘,，若電機絕緣下降請與本公司售后服務部聯系,，若緊固螺釘松動請重新緊固。

l 水泵在出廠前已注入適量的機油（32#機械油）,，用以潤滑機械密封,。該機油應每年檢查一次，如果發現機油呈乳化狀表示油中有水,，應將其放掉,，更換新機油，同時更換密封墊,，旋緊螺塞,。使用三個星期后應重新檢查，如果機油又呈乳化狀,，則機械密封損壞,，應及時更換，更換后應試氣（請與本公司售后服務部聯系）,。

In order to ensure the normal service life of the submersible pump, periodic inspection and maintenance should be carried out:

l Adjusting the bottom cover: After long-term use in water, the gap between the impeller and the bottom cover may increase, causing the flow and efficiency of the pump to decline. At this time, the power should be cut off, the pump lifted, the fixing screws loosened, and the bottom cover rotated. The gap is adjusted to 0.3 ～ 0.5mm (only for AS, AV and small pumps ≤7.5kW).

l Replace the seal ring: After long-term use in water, the gap between the impeller and the bottom cover may increase, causing the flow and efficiency of the pump to decrease. At this time, the power should be cut off, the pump lifted, the bottom cover removed, and the seal ring removed. The actual size of the impeller mouth ring is equipped with a seal ring, and the gap is generally about 0.5mm (≥ 11kW pump).

l When the pump is not used for a long time, it should be cleaned and lifted up and placed in a dry and ventilated place. If placed in water, run it for at least 30 minutes every 15 days (not dry-grinding) to check its function and adaptability. Pay attention to antifreeze in cold winter season.

l Check the cable at least once a year. If it is damaged, replace it immediately.

l Check the motor insulation and tightening screws at least once a year. If the motor insulation drops, please contact our after-sales service department. If the tightening screws are loose, please re-tighten them.

l The pump has been filled with an appropriate amount of oil (32 # mechanical oil) before leaving the factory to lubricate the mechanical seal. The oil should be inspected once a year. If it is found that the oil is emulsified to indicate that there is water in the oil, it should be removed, replaced with a new oil, and the seals should be replaced at the same time. After three weeks of use, it should be re-checked. If the oil is emulsified again, the mechanical seal is damaged and should be replaced in time. After the replacement, the gas should be tested (please contact our service department).

潛水排污泵（排污泵品牌）